A great set of 10 straight paring gouges all stamped “WARD” and bear the W&P anvil trade mark, all have boxwood handles and are clean steel, from largest down to smallest as follows.

  • 1 1/2” width sweep number 4 two shakes in handle 15 1/2” long.
  • 7/8” width sweep number 7 little Nick in handle next to ferrule, 15” long overall, minor nicks to cutting edge.
  • 3/4” width sweep number 7, ground outside, 14” long.
  • 7/8” width sweep number 5, 14 3/8” long.
  • 5/8” width sweep number 6, measures 14” in length.
  • 5/8” width sweep number 7, measures 13 3/4” long.
  • 7/16” width sweep number 7: 13 1/2” long.
  • 7/16” width sweep number 7 drying shake on handle 13 1/2” length.
  • 3/8” width sweep number 6 length is 13 1/4” long.
  • 1/4” width sweep number 7 length is 13”.
all chisels will require sharpening to your taste. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product visibility: outofstock.
Product categories: Paring Gouges.

A nice clean pointing trowel made in Sheffield England by “BOWDEN & Co” handle looks to have been revarnished at some point, the working face of trowel measures 5 1/2” long by 2 1/2” wide. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product categories: Bricklaying & Plastering Tools.

A hefty shave that measures 15” across, the handle is solid on the tang with no movement, the steel has lots of aged pitting so cannot see if its stamped with a maker, the curved cutting edge measures 3 1/2” across and is fairly sharp but has a couple of nicks along it, should think will hold a good edge once honed up. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product categories: Drawknifes and Inshaves & Scorps.

A vintage coopers jigger shave, it is stamped and could be WM GREAVES? Sheffield, it is also stamped “ELECTRO BORIC STEEL” the ash handle has no splits it is held on shaft by the tang that runs through handle, there is slightest of movement from side to side. The cutting edge measures 3” across  and you can tell the steel will hold a good edge but does require honing to taste., full length of the shave measures 15” across. Price is inclusive of postage to mainland a U.K. 
Read More

Product type: simple.
Product categories: Drawknifes and Inshaves & Scorps.

Only in production for a short period and now quite a scarce plane. Dates to 1954. No breaks to woodwork although varnish loss, clean steel, black jappaning paintwork may look better if refreshed, has been a working plane.  The X4 was MARPLES attempt at a top of the range smoothing plane.  Infill type rear handle and frog, adjustable mouth and the unique lever cap. Fitted with its original 2 inch round topped, chamfered back blade iron marked 'W.MARPLES & SONS SHEFFIELD ENGLAND' with the Shamrock trade mark. A rare plane to find these days. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product visibility: outofstock.
Product categories: Marple's.

This cutter could be bought as an addition for use with the RECORD 405 multi plane it is shown as reference A on the attached chart photo 1 1/2” width. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product categories: Cutters & Irons.

Additional 1/4” Reeding cutters for the RECORD Multi plane, these cutters are reference W, X, Y & Z shown on the chart in the photos, some discolouration marks from grease that protected them in storage. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product visibility: outofstock.
Product categories: Cutters & Irons.

Additional 3/16” Reeding cutters for the RECORD Multi plane, these cutters are reference S, T, U & V shown on the chart in the photos, some discolouration marks from grease that protected them in storage. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product visibility: outofstock.
Product categories: Cutters & Irons.

Additional 1/8” Reeding cutters for the RECORD Multi plane, these cutters are reference O,P,Q &R shown on the chart in the photos, some discolouration marks from grease that protected them in storage. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product visibility: outofstock.
Product categories: Cutters & Irons.

A set of 7 steel micro gouges. They are 9” long in length each has knurling grip shafts. They are stored in a cardboard roll. The smallest is 1/8” width then move up in following widths 3/16”.  7/32”.  1/4”.  5/16”.  5/16” and 3/8”. Price is inclusive of postage to mainland U.K. 
Read More

Product type: simple.
Product categories: Engineering Tools, Gouges and Pattern Makers Tools.